WiW 56

Tech Guide

How to Fix We Couldn’t Install Windows 10 Error (0XC1900101 – 0x20017)

Repair we could not set up Windows 10 0XC190010 — 0x20017, ” The setup failed at the SAFE_OS stage with a mistake during a BOOT operation. I encounter this odd error when attempting to update my Windows 7 PC into Windows 10 couple of days ago. This error is not exclusive to Windows 7 since you might also get this error even when you are operating Windows 8 or Windows 8.1 PC.

After trying several approaches mentioned on the internet and my alterations, I was eventually able to correct this and put in Windows 10. Thus, in the current article, we will see how to mend we could not install Windows 10 0XC190010 — 0x20017 from Windows 7 or Windows 8.1 operating PC.

What happens is that if you start the Windows 10 setup working with the Media production tool, the procedure reaches 100 percent and when the PC attempts to restart it is going to be stuck on Windows emblem with no motion or the PC will restart restoring your Windows version into What it had been previously which is Windows 8.1 or Windows 7.

If the PC restarts alone along with your drive shut down and restart the PC, then you will realize this we could not install Windows 10 0XC190010 — 0x20017 mistake saying installation failed from the SAFE_OS stage with an error through Boot operation.

This might be bothersome to anybody who has been excited about the setup of Windows 10 or even the update. However, after a couple of days of hunt and lots of reattempts, I managed to successfully set up Windows 10 on my Windows 7 operating PC by adjusting we could not install Windows 10 0XC190010 — 0x20017 malfunction.

Currently, there are lots of solutions available on the internet, but nothing worked for me. Therefore, within this short article, I will start with what used to work for me, and then we will take a look at what’s worked for many others. Thus, let’s begin.

Repair We could not set up Windows 10 0XC190010 — 0x20017

Two things I would like you to understand before proceeding with the repair.

  • You do not have to download the Windows 10 Setup files all again to update because your downloaded Windows 10 installation files are already stored on your C drive (in case you have not deleted them already). You need to have two folders on your own C:/ drive, also called as $Windows. ~BT and $Windows. ~WS. Your Windows 10 Setup files will be kept at $Windows. ~WS. Refer the below picture.

Update: You may also Discover the setup files in C:\ESD\Windows\ folder should don’t possess C:\$Windows. ~WS\Resources\Windows.

0XC1900101 – 0x20017

— Eliminate all of the External Hard drives, USB storage devices such as Network USB Dongle and some other external USB device attached to a PC.

Step 1: Create a Restore Point in your own Windows 8.1 or Windows PC

As we will be uninstalling some drivers out of the PC, I would suggest that you make a restore point on your Windows 7 or Windows 8.1 PC. Developing a Restore point would take several minutes. After the restore point was produced, proceed with different actions.

To make Restore Point, click on Start button, hunt for Restore Point, open Produce Restore point and wait till Windows generates a restore point. Restore stage will probably come in handy if something moves or rescue you from the frustration of installing the drivers again if you were unable to update to Windows 10.

Step 2: Uninstall Broadcom Bluetooth and Wireless Network Drivers

The next step will ask that you uninstall your Bluetooth and Wireless Network drivers. The Broadcom drivers installed onto your Windows 7, or Windows 8.1 PC is not compatible with Windows 10 for setup at least. This is right on my PC at the least.

Instead, should don’t wish to uninstall them, then just abandon it and have a chance by moving straight to Step 3.

 

Step 3: Eliminate Additional RAM

Now when you have added extra RAM for your PC (maybe not arrived with your PC), then you might have to remove it briefly also. For Dell users, eliminating RAM is simple, As you need to start the RAM compartment of your PC attached with one screw and remove the RAM. You may discover it in the rear of your computer, over the battery compartment. Additional PC users, kindly consult any direct on YouTube or visit your Producers website to find out more.

This solution may seem ridiculous to a couple of folks, but it is worked for a couple of users. So give it ago.

Step 4: Restart your PC and then Run the Setup

After confirming that you have followed all of the steps, restart your PC. When the PC restarts, visit C:\$Windows. ~WS\Resources\Windows folder and then operate on the Setup.exefile. This can initialize the Windows 10 setup procedure.

Update: You may also Discover the installation files in C:\ESD\Windows\ folder should don’t possess C:\$Windows. ~WS\Resources\Windows.

0XC1900101 – 0x20017

In case you have Windows 10 bootable USB Drive or Disk, then you may create a fresh install of Windows 10 on your PC. However, do note that, without updating your PC into Windows 10 first, should you create clean install then your Windows 10 won’t be triggered at no cost, and you might want to purchase the product key to activate it.

After all these measures did the job for me, and that I managed to update to Windows 10 out of Windows 7 Expert running PC. After updating to Windows 10, I will certainly tell that it worth all of the efforts I set to make it operate.

So, this is the way I updated to Windows 10 by adjusting the “we could not install Windows 10 0XC190010 — 0x20017, The setup failed at the SAFE_OS stage with a mistake during BOOT performance” error. Now let us have a peek at what worked for many others.

Some other method to Repair we could not set up Windows 10 0XC190010 — 0x20017 Error

If sadly even after following all of the above steps, you were unable to correct this error then you will need to try out the below-given tips.

  1. Unplug or Eliminate your Network Card

Some customers have reported that Unplugging Network Card has worked for them. So, mostly, you will need to get hold of the hardware to eliminate Network card in the PC or notebook computer. If you do not understand how to do this, then you might want to contact the closest service center or some other local PC repair shop to do that particular job. This can be temporary; it is possible to letter plug in the Network card after the Windows 10 was set up.

     2 .Eliminate all of the Unwanted Drivers Installed On Your PC

Have you got some undesirable drivers installed in your PC’s device manager? If the response is yes, then you might have to uninstall them and then attempt to update to Windows 10. Before uninstalling any software be certain that you make a restore point to be on the other hand.

Does nothing sound function? Take a look at Microsoft response thread for different repairs indicated by the users.

So, this was all about how to mend ” we could not install Windows 10 0XC190010 — 0x20017, The setup failed at the SAFE_OS stage with a mistake during BOOT performance ” error while installing Windows 10. Do let us know if that worked for you or in case you have any other fix for it. Do not’ forget to talk about this!

 

Leave a Reply

Your email address will not be published. Required fields are marked *

WiW 56 © 2017