If you have Blue Screen of Death (BSoD) problem together with the mistake Critical_Process_Died message popped up in your display, disrupting your job and causing your computer to restart, then you may let out a sigh of relief:
Now we have some options for you. BSoDs also referred to as STOP mistakes or STOP codes, which are a part of the Windows since Windows NT 3.1, which premiered in 1993. Considered by most consumers as the most annoying part of the operating system, those distinctive error messages are shown once a fatal system error occurs. Their objective is to tell the consumer about the possible cause and protect against harm to the machine.
Normal causes of BSoDs contain applications bugs, bad drivers, flawed memory, and power supply difficulties, overheating, and overclocking, only to mention a couple. You will find more than 500 known BSOD error codes, for example, code of 0x000000EF, which pertains to the Windows 10 mistake Critical_Process_Died.
- Your PC ran into an issue and had to restart. We are just gathering some mistake information, and then we will resume for you.
- If you want to learn more, you can hunt online later for this particular error: CRITICAL_PROCESS_DIED
Thus, you seek out the mistake simply to discover little to no helpful info. That is where this report comes in. Even when you are away from being a computer wizard that resides from the command line, then you will have the ability to eliminate this pesky BSOD right away.
What is the reason of Critical Process Died Error?
The Windows ensures that only authorized software can access specific data and regions of the system. When a crucial component of Windows finds an unauthorized alteration to its information, it instantly steps in, causing the Critical Process Died error to take place.
For instance, audio card drivers are notoriously filled with bugs, and the same applies to specific printers and wireless expansion cards. However, at times the reason for the error is not immediately apparent. You will find reports of this Critical_Proces_Died error occurring to owners of all brand-new notebooks, and it is not unheard of for the mistake to spontaneously begin happening on a computer that’s been running flawlessly for several years.
That is why it is paramount to bring a broader strategy and tackle multiple possible causes at the same time. You may begin at any strategy described in this guide or attempt them one by one–it is your decision. We highly advise that you perform through testing after each step you require, so you know that this alternative was the right one.
How to Fix Critical Process Died Error in Windows 10?
From poorly written device drivers to broken system files into viruses into defective storage devices, these options handle each these problems. You do not need to become a computer expert to employ them, either–only follow our directions and continue at your own pace.
Safe Mode and Clean Boot
Based on how heavy the issue is causing the Critical_Process_Died error goes, then you might be unable to boot your PC. This frequently occurs when a motorist is initialized when Windows loads up.
Safe Mode in Windows 10:
- Try booting a few times till you find a listing of three boot choices.
- Select Advanced alternatives.
- Click the Restart button.
If you can log in, you may even utilize Clean Boot, which begins Windows with a minimum set of drivers and startup apps.
Perform Clean Boot in Windows 10:
- Switch Enter to start the System Configuration program.
- Protect all providers you visit.
- Restart your PC.
The two Safe Mode and Clean Boot should temporarily repair the Critical_Process_Died mistake, enabling you to use the solutions described below.
Revert to the Previous Working State
Assuming your working system was functioning just fine until you have set up an update or even a new driver, the easiest solution how to eliminate this Critical_Process_Died error would be to revert to the prior working condition.
You may either manually uninstall the problematic part of the software or use System Restore to return in time and use automatically generated copies which Windows 10 kindly creates for you before every major upgrade or program change.
Use system restore in Windows 10:
- Kind “system restore.”
- Click the Create a restore point choice.
- Underneath System Protection, click System Restore…
- A dialogue window will appear and reveal restore points out there.
- Select any restore point you need and confirm your choice.
- Wait till Windows completes making changes.
While the restore attribute will not delete your files and documents, it might delete some settings and applications. Windows 10 enables you to scan for apps and drivers which are going to be removed once you revert to your prior edition. Note down them and reinstall them with extreme caution.
Aging system motorists can wreak havoc on any PC. Some hardware manufacturers provide handy software utilities which take good care of driver upgrades for you, but most leave this crucial process up for users.
When you get a new apparatus, go right to the official site of the producer and download the most recent drivers from this support page.